1. 配置DeviceA、DeviceB、DeviceC建立M-LAG系統。配置DeviceB和DeviceC的V-STP。配置DeviceB和DeviceC的DFS Group并綁定管理網口的IP地址。配置DeviceB和DeviceC之間的peer-link鏈路。配置DeviceB和DeviceC的M-LAG成員接口DeviceA的Eth-Trunk接口。配置DeviceB和DeviceC的Monitor Link功能。說明Monitor Link將上行接口和下行接口關聯避免因上行鏈路故障導致用戶側流量無法轉發而丟棄。在華為 CloudEngine (CE) 數據中心交換機上配置 M-LAG跨設備鏈路聚合核心邏輯分為四個部分心跳線 (Keepalive)、控制組 (DFS Group)、數據同步線 (Peer-link) 以及 下行成員接口 (M-LAG Interface)。以下是一套標準的 M-LAG 配置步驟與完整命令。步驟步驟配置DeviceA、DeviceB、DeviceC建立M-LAG系統。1.配置DeviceB和DeviceC的V-STP。#配置DeviceB。DeviceC的配置與DeviceB類似這里不再贅述。HUAWEIsystem-view[~HUAWEI]sysname DeviceB[*HUAWEI]commit[~DeviceB]stp mode rstp[*DeviceB]stp v-stp enable[*DeviceB]commit2.配置DeviceB和DeviceC的DFS Group并綁定管理網口的IP地址。DeviceB和DeviceC管理網口需要保證能夠三層互通。#配置DeviceB。DeviceC的配置與DeviceB類似這里不再贅述。[~DeviceB]dfs-group 1[*DeviceB-dfs-group-1]dual-active detection source ip 10.200.1.1 peer 10.200.2.1[*DeviceB-dfs-group-1]authentication-mode hmac-sha256 password YsHsjx_202206[*DeviceB-dfs-group-1]quit[*DeviceB]commit3.配置DeviceB和DeviceC之間的peer-link鏈路。#配置DeviceB。DeviceC的配置與DeviceB類似這里不再贅述。[~DeviceB]interface eth-trunk 1[*DeviceB-Eth-Trunk1]mode lacp-static[*DeviceB-Eth-Trunk1]trunkport 100ge 1/0/4[*DeviceB-Eth-Trunk1]trunkport 100ge 1/0/5[*DeviceB-Eth-Trunk1]peer-link 1[*DeviceB-Eth-Trunk1]quit[*DeviceB]commit4.配置DeviceB和DeviceC的M-LAG成員接口DeviceA的Eth-Trunk接口。#配置DeviceB。DeviceC的配置與DeviceB類似這里不再贅述。[~DeviceB]interface eth-trunk 10[*DeviceB-Eth-Trunk10]mode lacp-static[*DeviceB-Eth-Trunk10]port link-type trunk[*DeviceB-Eth-Trunk10]lacp mixed-rate link enable[*DeviceB-Eth-Trunk10]trunkport 100ge 1/0/2[*DeviceB-Eth-Trunk10]trunkport 100ge 1/0/3[*DeviceB-Eth-Trunk10]dfs-group 1 m-lag 1[*DeviceB-Eth-Trunk10]quit[*DeviceB]commit#配置DeviceA。HUAWEIsystem-view[~HUAWEI]sysname DeviceA[*HUAWEI]commit[~DeviceA]interface eth-trunk 10[*DeviceA-Eth-Trunk10]mode lacp-static[*DeviceA-Eth-Trunk10]port link-type trunk[*DeviceA-Eth-Trunk10]trunkport 100ge 1/0/1 to 1/0/4[*DeviceA-Eth-Trunk10]quit[*DeviceA]commit5.配置DeviceB和DeviceC的Monitor Link功能。#配置DeviceB。DeviceC的配置與DeviceB類似這里不再贅述。[~DeviceB]monitor-link group 1[*DeviceB-mtlk-group1]port 100ge 1/0/1 uplink[*DeviceB-mtlk-group1]port eth-trunk 10 downlink 1[*DeviceB-mtlk-group1]quit[*DeviceB]committip:在真實數據中心環境尤其是二層網絡中為了防止 M-LAG 分裂引發二層環路還需要配置V-STP (虛擬生成樹)或?qū)⑷?MAC 地址設置一致。對接下端設備服務器或接入交換機時下端設備只需將接口配置為普通的 LACP 動態鏈路聚合即可它會認為自己連接的是同一臺交換機。